US Robotics 56K USB MODEM - QUICK REV 2.0 Spezifikationen

TechMemo#01-0011B© Copyright 2001–2004 Adaptive Micro Systems LLC. All rights reserved.Adaptive Micro Systems • 7840 North 86th Street • Milwaukee, WI

August 26, 2004 TechMemo 01-0011B10 of 24Advanced modem setup using HyperterminalUse this section when AlphaNET Diagnostics software is not available

TechMemo 01-0011B August 26, 200411 of 245. Select COM1 from the next screen and click OK:6. When the next window appears, set the communication param

August 26, 2004 TechMemo 01-0011B12 of 24Configure the modem8. Configure the user-defined Y0 modem template by typing “at&h0&r1&b1&n6&

TechMemo 01-0011B August 26, 200413 of 24AppendixRelated documentationAlpha and AlphaEclipse sign data formatsPart # Manual title9711-7001 AlphaEclips

August 26, 2004 TechMemo 01-0011B14 of 24US Robotics V.90 and V.92 modem referenceDIP switchesDIP switchSetting(UP = off,DOWN = on)AT command equivale

TechMemo 01-0011B August 26, 200415 of 24Default modem settingsThese are the default or factory settings loaded into US Robotics 56K V.90 and V.90 Fax

August 26, 2004 TechMemo 01-0011B16 of 24AT commandsThe AT commands used in this section only apply to US Robotics 56K V.90 and V.92 Faxmodems.Though

TechMemo 01-0011B August 26, 200417 of 24InDisplays modem information:• I0 — 4-digit product code.• I1 — results of ROM checksum.• I2 — results of RAM

August 26, 2004 TechMemo 01-0011B18 of 24ZnResets modem. This works with DIP switch #7:• Z0 — reset modem to Yn. If DIP switch #7 = UP (off), then Y0,

TechMemo 01-0011B August 26, 200419 of 24&KnEnables or disables data compression:• &K0 — data compression disabled.• &K1 — auto enable/dis

August 26, 2004 TechMemo 01-0011B2 of 24AlphaEclipse outdoor sign modem setupOverviewTransmitting modem setup for AlphaEclipse outdoor signs1. Set the

August 26, 2004 TechMemo 01-0011B20 of 24&UnWith n > 0, sets the floor connect speed, lowest acceptable connection speed. &Nn is the ceilin

TechMemo 01-0011B August 26, 200421 of 24S registersThe S registers used in this section only apply to US Robotics 56K V.90 and V.92 Faxmodems.Registe

August 26, 2004 TechMemo 01-0011B22 of 24Bit-mapped registersTo set a bit-mapped register, select the bit(s) you want on and set the register (for exa

TechMemo 01-0011B August 26, 200423 of 24Settings for S27Settings for S32Settings for S333 8 Disable MNP handshake.4 16 Disable MNP level 4.5 32 Disab

August 26, 2004 TechMemo 01-0011B24 of 24Settings for S41Modem setup configuration stringThe following AT commands are used to set up a US Robotics 56

TechMemo 01-0011B August 26, 20043 of 243. Start AlphaNET Diagnostics software:4. When the Diagnostics screen appears, click Modem. Then make the foll

August 26, 2004 TechMemo 01-0011B4 of 24Receiving modem setup for AlphaEclipse outdoor signsThe receiving modem inside a sign was set up at the factor

TechMemo 01-0011B August 26, 20045 of 24Alpha indoor sign modem setupOverviewTransmitting modem setup for Alpha signs1. Set the DIP switches on the ba

August 26, 2004 TechMemo 01-0011B6 of 24Receiving modem setup for Alpha indoor signs1. Set the DIP switches on the back of the receiving modem as show

TechMemo 01-0011B August 26, 20047 of 24Modem testThe following procedure tests to see if the transmitting and receiving modems are working correctly.

August 26, 2004 TechMemo 01-0011B8 of 243. Click Edit and set up the modem device as shown below:4. Click OK until just the Site Manager screen appear

TechMemo 01-0011B August 26, 20049 of 245. From the Site Manager screen, click File > New Site. Set up the new site as shown below. Then click OK:6